CWNP CWNA-109 Practice Exam Questions & Answers
CWNP CWNA-109 Exam Details
Key details for this exam, checked against the published exam outline
- Exam Code
- CWNA-109
- Full Name
- Certified Wireless Network Administrator
- Issuing Body
- CWNP (Certified Wireless Network Professionals)
- Question Format (Our Bank)
- Multiple Choice
- Delivery
- Online proctored or at a Prometric testing center
- Eligibility
- No prerequisites required. Recommended: basic networking knowledge, basic TCP/IP knowledge, at least 1 year wireless LAN work experience
- Validity
- 3 years
- Full Question Set
- 122 questions Get All Questions
Free CWNA-109 Practice Questions
Each question shows the correct answer and an explanation of why it is right
Question 1 Domain 5 RF Validation and WLAN Remediation
You are performing a post-implementation validation survey. What basic tool can be used to easily locate areas of high co-channel interference?
Question 2 Domain 3 WLAN Network Architecture and Design Concepts
You manage a WLAN with 100 802.11ac access points. All access points are configured to use 80 MHz channels. In a particular BSS, only 40 MHz communications are seen. What is the likely cause of this behavior?
The clients are all 802.11n STAs or lower is the likely cause of this behavior. If a WLAN with 100 802.11ac access points is configured to use 80 MHz channels, but only 40 MHz communications are seen in a particular BSS, it means that the clients in that BSS do not support 80 MHz channels. This could be because they are using older standards, such as 802.11n or lower, that do not support 80 MHz channels. Alternatively, they could be using newer standards, such as 802.11ac or ax, but have their channel width settings limited to 40 MHz or lower due to device capabilities or configuration options. In either case, the AP will adapt to the client's channel width and use only 40 MHz of the 80 MHz allocated bandwidth to communicate with them. This will reduce the potential throughput and efficiency of the WLAN.Reference:, Chapter 3, page 111; , Section 3.2
Question 3 Domain 6 Radio Frequency (RF) Technologies
A client complains of low data rates on his computer. When you evaluate the situation, you see that the signal strength is -84 dBm and the noise floor is -96 dBm. The client is an 802.11ac client and connects to an 802.11ac AP. Both the client and AP are 2x2:2 devices. What is the likely cause of the low data rate issue?
Weak signal strength is the likely cause of the low data rate issue for the client that has a signal strength of -84 dBm and a noise floor of -96 dBm. The client is an 802.11ac client and connects to an 802.11ac AP. Both the client and AP are 2x2:2 devices. Signal strength is the measure of how strong the RF signal is at the receiver. Signal strength can affect the reliability and performance of the wireless connection, as well as the data rate and throughput of the traffic. The higher the signal strength, the better the signal quality and the higher the data rate. The lower the signal strength, the worse the signal quality and the lower the data rate.
The data rate of an 802.11ac connection depends on several factors, such as channel bandwidth, modulation and coding scheme (MCS), spatial streams, guard interval, and beamforming. However, these factors are also influenced by the signal strength, as they require a certain signal-to-noise ratio (SNR) to operate properly. SNR is the ratio of the signal strength to the noise floor, which is the measure of the background noise or interference in the RF environment. The higher the SNR, the more robust and efficient the communication. The lower the SNR, the more prone and vulnerable to errors and retries.
According to the CWNA Official Study Guide , Table 3.7, page 112, an 802.11ac connection with a channel bandwidth of 80 MHz, an MCS of 9, two spatial streams, a short guard interval, and no beamforming can achieve a maximum data rate of 867 Mbps. However, this data rate requires a minimum SNR of 30 dB to maintain a sufficient signal quality. If the signal strength is -84 dBm and the noise floor is -96 dBm, then the SNR is only 12 dB (-84 dBm - (-96 dBm) = 12 dB), which is far below the required SNR for this data rate. Therefore, the data rate will drop significantly to match the lower SNR and signal quality.
To solve this problem, the signal strength should be increased to improve the SNR and data rate. This can be done by adjusting the output power or channel assignment of the AP or client, relocating or reorienting some APs or antennas to reduce attenuation or interference, updating or replacing some faulty or outdated hardware or software components, etc.Reference:, Chapter 3, page 112; , Section 3.2
Get the complete CWNA-109 question set
$20$40
Question 4 Domain 3 WLAN Network Architecture and Design Concepts
An RF signal sometimes bends as it passes through some material other than free space. What is the term that describes this behavior?
Question 5 Domain 2 WLAN Protocols and Devices
You are a small business wireless network consultant and provide WLAN services for various companies. You receive a call from one of your customers stating that their laptop computers suddenly started experiencing much slower data transfers while connected to the WLAN. This company is located in a multi-tenant office building and the WLAN was designed to support laptops, tablets and mobile phones. What could cause a sudden change in performance for the laptop computers?
A possible cause of a sudden change in performance for the laptop computers is thata new tenant in the building has set their AP to the same RF channel that your customer is using. This can create co-channel interference (CCI), which is a situation where two or more APs or devices use the same or overlapping channels in the same area. CCI can degrade the performance of WLANs by increasing contention, collisions, retransmissions, and latency. CCI can also reduce the effective range and throughput of WLANs by lowering the signal-to-noise ratio (SNR). To avoid or mitigate CCI, it is recommended to use non-overlapping channels, adjust transmit power levels, or implement channel management techniques such as dynamic frequency selection (DFS) or load balancing. The sky condition, antenna position, or Bluetooth headset are not likely to cause a sudden change in performance for the laptop computers.Reference:[CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 81; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 71.
Question 6 Domain 4 WLAN Network Security
An RF signal sometimes bends as it passes through a material rather than around an obstacle. What is the RF behavior that this statement best describes?
Question 7 Domain 5 RF Validation and WLAN Remediation
What statement about 802.11 WLAN performance is true?
What the CWNP CWNA-109 Exam Covers
Exam domains verified against the Official CWNP CWNA-109 exam guide, last checked November 2026.
Domain 1 WLAN Regulations and Standards
Learn the roles of IEEE, Wi-Fi Alliance, IETF, and regulatory agencies in setting WLAN standards. Study Physical Layer solutions from 802.11 through 802.11ax including DSSS, OFDM, and the latest Wi-Fi 6 technologies with their supported data rates and channel widths.
Domain 2 WLAN Protocols and Devices
Master 802.11 MAC and PHY terminology, frame types and formats, and channel access methods. Know how wireless devices communicate using different frame structures and the protocols that govern access to the wireless medium.
Sample question from this domain above Q5
Domain 3 WLAN Network Architecture and Design Concepts
Implement Power over Ethernet for access points and design wireless LAN architectures. Address coverage requirements, roaming considerations, and common proprietary features that enterprises use to optimize network performance.
Domain 4 WLAN Network Security
Identify weak security options and implement enterprise WLAN security mechanisms. Evaluate security tools and options for wireless networks to protect against unauthorized access and data compromise.
Sample question from this domain above Q6
Domain 5 RF Validation and WLAN Remediation
Manage RF interference and optimize WLAN performance using validation tools. Troubleshoot common wireless issues through understanding tool features and applying remediation techniques for real-world network problems.
Domain 6 Radio Frequency (RF) Technologies
Understand RF basics, mathematics, and measurement including signal characteristics, antenna functionality, RF cables, connectors, grounding, and enclosures. This domain covers fundamental RF behavior needed for wireless network deployment and troubleshooting.
Sample question from this domain above Q3
Domain 7 WLAN Regulations and Standards
Learn the roles of IEEE, Wi-Fi Alliance, IETF, and regulatory agencies in setting WLAN standards. Study Physical Layer solutions from 802.11 through 802.11ax including DSSS, OFDM, and the latest Wi-Fi 6 technologies with their supported data rates and channel widths.
Domain 8 WLAN Protocols and Devices
Master 802.11 MAC and PHY terminology, frame types and formats, and channel access methods. Know how wireless devices communicate using different frame structures and the protocols that govern access to the wireless medium.
Domain 9 WLAN Network Security
Identify weak security options and implement enterprise WLAN security mechanisms. Evaluate security tools and options for wireless networks to protect against unauthorized access and data compromise.
Domain 10 RF Validation and WLAN Remediation
Manage RF interference and optimize WLAN performance using validation tools. Troubleshoot common wireless issues through understanding tool features and applying remediation techniques for real-world network problems.
CWNA-109 Exam FAQ
Common questions about the exam itself
What background do I need before taking the CWNA-109 exam?
How difficult is CWNA-109 compared to other CWNP certifications?
Which domain do most candidates struggle with on CWNA-109?
How long should I study for CWNA-109?
What happens on exam day for CWNA-109?
Can I retake CWNA-109 if I fail?
How long does the CWNA-109 certification stay valid?
What jobs does CWNA-109 prepare me for?
Is CWNA-109 a prerequisite for other CWNP certifications?
How has CWNA-109 changed from the previous CWNA-108 version?
Other CWNP Exams
Free practice questions for more CWNP certification exams
